KPT1-20-35 belt conveyor deviation switch correction sensor KPT1-20-35 belt conveyor deviation switch correction sensor Belt Switch, also known as anti deviation switch. It is a product used to detect the deviation of the conveyor belt of a belt conveyorA safety protection device that automatically alarms and stops the conveyor belt in case of deviation. Introduction: The deviation switch has two levels of angles. The commonly used ones are: the first level angle is 10, 12, and 20. The second level angle is 30, 35, and 45. The basic principle is that when the conveyor belt deviates during operation, the conveyor belt touches the switch vertical roller and causes it to deviate. When the deviation angle of the vertical roller reaches the first level switch angle, the switch sends an alarm signal. When the conveyor belt deviates seriously and reaches the second level switch angle, the switch sends a stop signal to automatically stop the conveyor belt due to deviation fault. When the deviation fault is eliminated and the tape machine is running normally, the switch vertical roller can automatically reset and return to the initial state< Installation and adjustment: 1. The deviation switch should be set on both sides of the conveyor belt, and the vertical rollers should be perpendicular to the edge plane of the conveyor belt, and the two sides of the conveyor belt should be located at 1/3 of the height of the vertical rollers. The distance between the vertical roller of the deviation switch and the normal position of the conveyor belt should be 50-100mm. The number of deviation switches should be determined based on the length, type, and layout of the conveyor. Generally, it should be set at the head, tail, convex arc section, concave arc section, and in the middle position of the conveyor. (Note: When the conveyor is long, one pair can be installed every 30-35 meters in the middle position of the conveyor.) 4. The deviation switch should be connected to the middle frame of the conveyor through an installation bracket. The switch bracket should be welded to the conveyor frame after the conveyor is installed. The deviation switch and the deviation switch bracket should be fixed with bolts. Scope of application: Two level deviation switch for conventional belt conveyors: underground, cable support belt conveyors: ship loading and unloading systems; Stacking/reclaiming conveyor; Tilt and shuttle conveyors; Crane, excavator, boom limit: skirt feeder/conveyor: heavy-duty limit switch detects the deviation of the tape, which is a protective device for automatic alarm and shutdown of the tape machine control. Widely used in various belt conveyor equipment in fields such as metallurgy, coal, cement and building materials, mining, electricity, ports, metallurgy, chemical industry, etc< Technical indicators 1 Rated voltage: AC380V2. Rated current: 5A3 Number of contacts: Two independent normally open and normally closed contacts. 4. Housing protection level: DT type dustproof housing, protection level IP67. 5. Surrounding environment temperature: -25~80 ℃. 6. The switch can operate under vibration conditions with a frequency of 10-60Hz and an amplitude of 0.75mm (10g). 7. External dimensions: Housing L x W x H (mm) 190 x 135 x 100. 8. Operating power: 5-7 kg. 9. Communication interface: RS485 address code network communication (valid for models with suffix BM) KLT2-2 rope switch KLT2-1. Usage: This series of bidirectional rope switches is mainly used as a protective device for emergency parking of conventional belt conveyors, shuttle conveyors, skirt type feeding conveyors, bucket elevators, packaging production lines, stacking/reclaiming systems, cranes, excavators, ship loading and unloading systems, horizontal feeders, and other equipment on site. When an emergency occurs, pulling the rope switch at any location along the site can issue a shutdown signal, achieving protection for personnel and equipment< Equipment description: ● The pull switch is bi-directional and can be installed in the middle or at both ends of the conveyor< The universal installation design allows the pull switch to be installed on either the top or both sides of the conveyor longitudinal beam< Durable cast aluminum shell with a protection level of IP65, and special surface treatment for special environments< The integral cover plate makes wiring and switch adjustment convenient and simple, without the need to disassemble the switch, and the structural design is compact< The JYB/KS III eye-catching reflective flap flag complements the red shell, making it easy to distinguish between alarms or normal states< Provide complete accessories, including wire ropes, rope clamps, and cable support bolts, as well as manual lever reset. ◆ Environmental conditions for use:
a. Environmental temperature: -40 ℃~60 ℃
b. Relative humidity not exceeding 85%
c. Sea level not exceeding 2000m
d. Service life: 100000 switch actions
e. Insulation voltage: AC1000 test for 1 minute ◆ Main technical indicators: contact capacity, number of contacts, action force (Kg), reset form, working stroke limit stroke protection level weight (Kg), normally open and normally closed KLT2- Ⅰ ≤ 380V ≤ 2A1112± 2 automatic reset 15± 2mm20± 2mmIP552.5KLT2-Ⅱ≤380V ≤ 2A1112± 2 manual reset 15± 2mm20± Working principle and structural features: This machine adopts a mobile cam structure. When either side of the rope switch is pulled or both sides of the rope are pulled at the same time, the cam can be driven to switch the switch action and send out shutdown and alarm signals. The KLT2-I bidirectional tension switch adopts an automatic reset method. The KLT2-II bidirectional tension switch adopts a manual reset method. After troubleshooting, the operator must pull out the reset lever upwards in order to restore the machine to normal operation. 6-36 (V) slot type photoelectric switch: E3S-GS7N1 E3S-GS7N2、E3S-GS7P1、E3S-GS7P2、E3S-GS7Y1、E3S-GS7Y2。 E3S-GS15N1、E3S-GS15N2、E3S-GS15P1、E3S-GS15P2、E3S-GS15Y1、E3S-GS15Y2。E3S-GS20N1、E3S-GS20N2、E3S-GS20P1、E3S-GS20P2、E3S-GS20Y1、E3S-GS20Y2。E3S-GS30E4、E3S-GS30E2、E3S-GS30P1、E3S-GS30P2、E3S-GS30Y1、E3S-GS30Y2。 Replace contact detection methods such as limit switches. It has the advantages of small size, high sensitivity, fast frequency response, high repeated positioning accuracy, short transient process, large output power, good emergency characteristics, stable and reliable operation, and long service life. Square and slot type inductive proximity switch LJG5C-4/Z2CN2, LJG5C-4/Z2BN2 , LJG5C-4/Z2CP2 , LJG5C-4/Z2BP2 , LJG5C-4/Z0AN2 LJG5C-4/Z0BN2 , LJG5C-5/Z2CN2, LJG5C-5/Z2BN2 , LJG5C-5/Z2CP2, LJG5C-5/Z2BP2   LJG5C-5/Z0AN2 , LJG5C-5/Z0BN2 , LU3-10N1, LU3-10N2 , LU3-10P1, LU3-10P2,LU4-16N1 ,     LU4-16N2, LU4-16P1, LU4-16P2, LU4-16D1, LU4-16D2,LU5-16N1, LU5-16N2, LU5-16P1    LU5-16P2, LU5-16D1, LU5-16D2, JKS-J-D,LU5-15N1,LU5-15N2, LU5-15P1,LU5-15P2   LU5-15D1, LU5-15D2, JKD-J-D12,SK-3015A,SK-3015B,SK-3015AB, SK-3015C,SK-3015D SK-3015CD, SK-3015AL, SK-3015BL,SK-2015A,SK-2015B,SJ-3018A,SJ-3018B, SJ-3018AB, SJ-3018C,SJ-3018D,SJ-3018CD,SJ-3018AL,SJ-3018BL,SJ-2018A,SJ-2018B,SD-3020A,SD-3020B,SD-3020AB,SD-3020C,SD-3020D,SD-3020CD,SD-3020AL,SD-3020BL,SD-2020A,SD-2020B,SD-2020AB SE-3025A SE-3025B SE-3025AB   SE-3025C SE-3025D, SE-3025CD   SE-3025AL,SE-3025BL, SE-2025A, SE-2025B, SE-2025AB, TCO-3040A,TCO-3040B TCO-3040AB,TCO-3040C,TCO-3040D,TCO-3040CD,TCO-3040AL,TCO-3040BL, TCO-2040A TCO-2040B,TCO-2040AB,TCA-3050A,TCA-3050B,TCA-3050AB,TCA-3050C,TCA-3050D, TCA-3050CD,TCA-3050AL,TCA-3050BL,TCA-2050A,TCA-2050B,TCA-2050AB, TCB-3080A TCB-3080B,TCB-3080AB,TCB-3080C,TCB-3080D,TCB-3080CD,TCB-3080AL, TCB-3080BL, TCB-2080A,TCB-2080B,TCB-2080AB,TCC-30120A,TCC-30120B,TCC-30120AB,TCC-30120C,TCC-30120D,TCC-30120CD, TCC-30120AL, TCC-30120BL ,TCC-20120A ,TCC-20120B , TCC-20120AB, Capacitive proximity switch LJC12A3-A-Z/AX, LJC12A3-A-Z/BY, LJC12A3-A-Z/AY ,LJC18A3-5-Z/BX, LJC18A3-5-Z/AX LJC18A3-5-Z/BY, LJC18A3-5-Z/AY ,LJC18A3-B-Z/BX , LJC18A3-B-Z/AX, LJC18A3-B-Z/BY LJC18A3-B-Z/AY,LJC24A3-8-Z/BX, LJC24A3-8-Z/AX , LJC24A3-8-Z/BY , LJC24A3-8-Z/AY LJC24A3-8-J/EZ, LJC24A3-8-J/DZ , LJC18A3-B-J/DZ, LJC18A3-5-J/DZ, LJC18A3-5-J/EZ LJC18A3-B-J/EZ,LJC24A3-T-Z/BX, LJC24A3-T-Z/AX, LJC24A3-T-Z/BY , LJC24A3-T-Z/AY LJC24A3-T-J/EZ,LJC24A3-T-J/DZ ,LJC30A3-10-Z/BX, LJC30A3-10-Z/AX ,LJC30A3-10-Z/BY LJC30A3-10-Z/AYLJC30A3-10-J/EZ LJC30A3-10-J/DZ， LJC30A3-H-Z/BX LJC30A3-H-Z/AX LJC30A3-H-Z/BY LJC30A3-H-Z/AY LJC30A3-H-J/EZ LJC30A3-H-J/DZ LJC34A3-K-Z/BX LJC34A3-K-Z/AX LJC34A3-K-Z/BY LJC34A3-K-Z/AY LJC34A3-K-J/EZ LJC34A3-K-J/DZ LJC20A4-10-Z/BXLJC20A4-10-Z/AX LJC20A4-10-Z/BY LJC20A4-10-Z/AY LJC20A4-10-J/EZ LJC20A4-10-J/DZLJC38A4-20-Z/BX LJC38A4-20-Z/AXLJC38A4-20-Z/BY LJC38A4-20-Z/AY LJC38A4-20-J/EZ LJC38A4-20-J/DZLJC80A4-40-Z/BX LJC80A4-40-Z/AXLJC80A4-40-Z/BY LJC80A4-40-Z/AY LJC80A4-40-J/EZ LJC80A4-40-J/DZ LJC12A3-2-Z/BX, LJC12A3-2-Z/AX, LJC12A3-2-Z/BY ,LJC12A3-2-Z/AYLJC12A3-A-Z/BX simulation, Hall type proximity switch J4-D8V JCW-30QA; JCW-40QA JCW-48QA   NJK-5001C NJK-5001D   NJK-5001ANJK-5001B NJK-5002C NJK-5002D NJK-5002CD NJK-5002A NJK-5002B NJK-5002ABNJK-8002C NJK-8002D NJK-8002CD NJK-8002A NJK-8002B NJK-8002AB NJK-5003C NJK-5003D NJK-5003CD NJK-5003A NJK-5003B NJK-5003AB